3014 LED lamp beads (SMD) Model: 3014 SMD Current: 30MA Power: 0.1W Voltage: 2.8-3.4 V Color: White 5700-6100K 6100-6500K Natural white 4000-4500K Warm white 2800-3200K Lumen: 10-13LM a , 3014 LED lamp bead bead size small 3014 SMD LED is a highlight and low-cost LED lamp lighting product development direction now on the market are both light, thin, small line, our SMD LED relative to other His LED, the thinner, more convenient design. From 3014 the name you know, and ordinary SMD LED beads compared to 3014 is one of the advantages of small size, only (3.0 * 1.4 * 0.8 mm) two, 3014 LED lamp beads high brightness, brightness 3014 is the industry's highest brightness single, reaching 10-13lm three, 3014 LED lamp beads low light. Use metal stents vertical heat, good thermal conductivity, low thermal resistance; and the LED at normal temperature test, better than normal patches. Fourth, the color temperature consistency, delivery short delivery, a voltage of 0.1V BIN, a color temperature of 400K Bin, such that we can meet customer delivery, to meet customer requirements supply 3014 SMD 3014LED fluorescent lamp beads 3014 3014 piece lamp beads experimental data: 1, color rendering index: Should certain customer requirements, our company 3014 lamp beads can meet international standards Ra = 80 or more. (Note: The color rendering index and luminous flux is inversely proportional to please customers measure based on availability). 2. color tolerance index: Our 3014 SMD LED beads should be some customer requirements to meet international standards within less than 5. (Note: The color tolerance index and the naked eye to see the actual color 3014LED white there is a certain asymmetry, it is possible to color tolerance index is high, but the actual color white 3014LED your company's customers can not accept, customers based on actual case measure). 3, luminous efficiency: the current internationally accepted LED white light effect is 60-90lm / W, while Japan and certain types of white LED luminous efficiency can reach 100-120LM / W's. 4, the electrical resistance index: very stable. Jin Haibin 3014 SMD LED beads in the context of a constant voltage, current fluctuations small. 5, solderability and resistance to soldering: After two seconds in the 100 LED white End Baptist tin stoves, welding rate of 100%; 10 seconds immersion tin without leakage. 6, vibration resistance: vibration analyzer with continuous shaking 72 hours and then to use without any exception. 7, resistance to thermal resistance: at high temperature being 80 degrees and minus 35 degrees temperature lamp beads 3014 I can still work and ten thermal cycles without leakage and dead lights. 8. Consistency: large quantities of fixed-band chip production, 3014 to ensure delivery to the customer and shipped 2, 3014 lamp beads ensure excellent color temperature consistency over 3014 SMD LED beads experimental data were confirmed by our quality control department! and research and development for at least 30 experiments concludes! We recommend using 3014 lamp beads data: 1, the proposed drive current: 10-16mA; Maximum current proposal should not exceed 30mA. 2, instant driving voltage and reverse voltage can not exceed 5V, or to damage to the LED lamp beads or severely damaged beyond repair. 3, ambient temperature -30 ℃ ~ + 60 ℃, recommendations thermally optimized design of lamps, the LED white light pin negative temperature is below 60 degrees. 4,3014 lit lamp beads allows a maximum number of hours per day to 18 hours of continuous light for 3014 lamp beads life will have been affected. 5. If the current 10-20mA time, each lower 1mA current, the flux corresponding decrease of 4%; customers can thus calculate the luminous flux white LED work time. 7, all need touch 3014LED lamp beads operators must wear a truly effective anti-static wrist strap. 8,3014LED pin bent if necessary, break point from 3014LED colloid must go beyond more than 3mm; 9,3014 lamp beads of solder normal requirement is 260 ℃ ± 3 ℃, welding time shall more than two seconds, if it is too tin stove, tin furnace temperature is below 275 ℃, immersion tin no longer than 2 seconds, and requires the operator to operate 3014, when the action is very skilful and precise. 10,3014 lamp beads, when wave soldering, wave soldering machines claim to be truly grounded. When the ground wire must not be connected to the utility grid above ground, it must be connected to the utility grid completely separated from a true earth ground. This leads directly into the ground wire requires damp underground depth of 5 meters or less. Note: Many users do not notice it, which leads to a direct wave machine electrostatic breakdown LED chip, resulting in 3014LED lamp beads and little light leakage or dead lights. 11, 3014 all local or equipment and raw materials in contact with the lamp beads have connected real ground. 12, the detection of the 3014 and 3014 lamp beads lamp beads into the PCB board this procedure, be very careful, must do triple protection: the first heavy, the operator must wear a truly effective anti-static hand ring. The second heavy work table must be anti-static rubber blanket. The third tier, in front of the operator must assemble an ion fan (except for static fan) to eliminate static electricity. 13,3014LED light board before making good power-testing, be sure to determine the lamp is not connected to a circuit board tin tin short circuit, if the short-circuit, this will definitely have 3014LED lamp beads damaged or severely damaged, or immediately began to unravel, or to lead was revealed a few days or longer, resulting in a hidden hazard, so be sure to carefully check the circuit first case, which appeared in 5630 a lot of customers who use a lot of times, this is especially particular attention! ! ! 3014 SMD LED beads Application: 3014 SMD LED lamp beads can be widely used in fluorescent lamps, LED spotlights, LED panel lights, LED ceiling light, LED bulb lights, indoor lighting and outdoor lighting above.